Often asked: How To Change Heating Element On Whirlpool Dryer?

How much does a heating element cost for a Whirlpool dryer?

How Much Does a Heating Element Cost for a Dryer? A new heating element is usually between $40 and $100. This part might cost as low as $30 and as high as $200 or more, depending on the type of dryer.

Where is the heater coil on a Whirlpool dryer?

Whirlpool usually locates the heating element on the back of dryer (must remove back of dryer) or under the drum (must remove front dryer). Be certain to disconnect power from dryer. Heating element coils look like stretched out door springs. A bad dryer heating element will have a break in the coil.

How do you tell if the heating element is bad in a dryer?

Inspect the metal wire coil for any breaks in the wire. If the wire is solid and has no breaks in it, the heating element should be good. If the wire has a break in it, the heating element is defective.

You might be interested:  Readers ask: How To Clean Vaporizer Heating Element?

Why is my dryer running but not heating?

Is your dryer not heating up? Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.

Is dryer heating element hard to replace?

Fortunately, replacing a heating element isn’t a terribly difficult job. You can usually find a replacement heating element at a local hardware store or online by searching for your dryer model number. Once you have the part, unplug the dryer, remove the back panel, remove the connections and install the new one.

What does it mean when your dryer blows out cold air?

One of the most common reasons your tumble dryer decides to blow out cold air instead of hot is, rather ironically, because it has overheated. If your tumble dryer does not have a reset button it is likely you will need to replace your thermostat and thermal overload cut-out (TOC).

What causes a heating element to burn out in a dryer?

A dryer’s heating element operates on the same principle as the coil in an electric heater. It consists of an uninsulated metal conductor and when an electric current passes through it, its resistance to the flow of electricity makes it heat up. If the coil gets too hot, it burns out.

Do all Whirlpool dryers have the same heating element?

Whirlpool electric dryer heating elements are located in different locations on the machine depending on the model of dryer that you own. For a large amount of electric Whirlpool dryers have the heating element is located in the back of the dryer.

You might be interested:  Often asked: How To Replace A Heating Element In A Stove?

When should I replace the heating element in my dryer?

If your dryer takes longer than usual to dry your clothes, or the air in the dryer never heats, your heating element might be bad. You can test your heating element to determine whether you need to replace it. Unplug your dryer from the utility room wall outlet.

What would cause a whirlpool dryer not to heat?

When gas or electric Whirlpool Dryer is not heating up, it usually caused by: Burnt Heating Element or Gas Valve Solenoid, Burnt Thermal Cut-Off Fuse, Defective Cycling Thermostat Or Gas Ignitor, Malfunctioned Flame Sensor.

How do I know if my thermal fuse is blown?

How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.

How do you fix a dryer that is not heating?

This is the most common cause of a dryer not heating. To check if your venting is clogged, start a timed dry on high heat. Go to the exhaust vent outside and use your hand to verify that the air is very warm and exiting at a decent flow. If there’s little airflow, your venting likely needs to be cleaned or replaced.

How long does a heating element last in a dryer?

The heating element can last between 8 and 18 years if the dryer is well-maintained and the vent and lint traps are clean. The heating element can burn out if the dryer is not kept well-maintained.

Leave a Reply

Your email address will not be published. Required fields are marked *