Often asked: How To Change The Heating Element On Whirlpool Dryer?

Where is the heater coil on a Whirlpool dryer?

Whirlpool usually locates the heating element on the back of dryer (must remove back of dryer) or under the drum (must remove front dryer). Be certain to disconnect power from dryer. Heating element coils look like stretched out door springs. A bad dryer heating element will have a break in the coil.

Is it worth replacing a heating element in a dryer?

If your dryer’s heating element burns out more than once within a year or two, the thermal fuse, which is supposed to protect it, is probably defective, so it’s a good idea to replace it. The temperature in the heating chamber may also be too high, and that may be caused by poor venting.

How do you tell if the heating element is bad in a dryer?

Inspect the metal wire coil for any breaks in the wire. If the wire is solid and has no breaks in it, the heating element should be good. If the wire has a break in it, the heating element is defective.

You might be interested:  Quick Answer: What Is The Cist Of A New Heating Element For A Kenmore Dryer?

Why is my dryer running but not heating?

Is your dryer not heating up? Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.

How can you tell if heating element is bad?

Touch the needle on the end of the tester to the other terminal. If the light inside the continuity tester glows, the heating element is good. If the tester fails to glow, the heating element needs replacing.

What causes a heating element to burn out in a dryer?

A dryer’s heating element operates on the same principle as the coil in an electric heater. It consists of an uninsulated metal conductor and when an electric current passes through it, its resistance to the flow of electricity makes it heat up. If the coil gets too hot, it burns out.

How hard is it to replace a dryer heating element?

Fortunately, replacing a heating element isn’t a terribly difficult job. You can usually find a replacement heating element at a local hardware store or online by searching for your dryer model number. Once you have the part, unplug the dryer, remove the back panel, remove the connections and install the new one.

How do you fix a dryer that is not heating?

This is the most common cause of a dryer not heating. To check if your venting is clogged, start a timed dry on high heat. Go to the exhaust vent outside and use your hand to verify that the air is very warm and exiting at a decent flow. If there’s little airflow, your venting likely needs to be cleaned or replaced.

You might be interested:  Quick Answer: How To Install A New Heating Element On Stove Top?

Is it cheaper to repair or replace a dryer?

The national average cost for dryer repair is $170. If your dryer is acting strange, investing in repair services is usually much cheaper than buying a replacement dryer. New dryers cost anywhere from $400 for entry-level to $2,000, or more, for top of the line.

How much does it cost to fix a dryer that is not heating?

Fixing a dryer that does not heat averages $100 to $350. The price for this repair depends on the problem. It might be a problem with the heating element or an issue with the thermostat or igniter when using a gas dryer.

How do I know if my thermal fuse is blown?

How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.

How long does a heating element last in a dryer?

The heating element can last between 8 and 18 years if the dryer is well-maintained and the vent and lint traps are clean. The heating element can burn out if the dryer is not kept well-maintained.

When I press the start button on my dryer nothing happens?

If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. If it doesn’t turn on, it’s likely that the dryer has no power. Check your power cord and the house circuit breaker.

Leave a Reply

Your email address will not be published. Required fields are marked *