Question: How To Replace Heating Element 279838 In Whirlpool Dryer?

How do I know if my dryer heating element is bad?

Unplug the dryer when checking the heating element. It is a long coil of wire inside a metal can. Check it with an ohm meter. If there is no continuity, replace the heating element.

Is it worth replacing a heating element in a dryer?

If your dryer’s heating element burns out more than once within a year or two, the thermal fuse, which is supposed to protect it, is probably defective, so it’s a good idea to replace it. The temperature in the heating chamber may also be too high, and that may be caused by poor venting.

Are dryers worth repairing?

Is it worth repairing a dryer? Dryer repairs are worth it if the appliance is less than 4 years old and the cost is less than $400. For older dryers and/or costly repairs, replacing your appliance is more cost effective.

You might be interested:  How Does A Heating Element In Water Work?

What causes a heating element to burn out in a dryer?

A dryer’s heating element operates on the same principle as the coil in an electric heater. It consists of an uninsulated metal conductor and when an electric current passes through it, its resistance to the flow of electricity makes it heat up. If the coil gets too hot, it burns out.

How do you fix a dryer that is not heating?

This is the most common cause of a dryer not heating. To check if your venting is clogged, start a timed dry on high heat. Go to the exhaust vent outside and use your hand to verify that the air is very warm and exiting at a decent flow. If there’s little airflow, your venting likely needs to be cleaned or replaced.

How can you tell if heating element is bad?

Touch the needle on the end of the tester to the other terminal. If the light inside the continuity tester glows, the heating element is good. If the tester fails to glow, the heating element needs replacing.

How long do heating elements last in a dryer?

The heating element can last between 8 and 18 years if the dryer is well-maintained and the vent and lint traps are clean. The heating element can burn out if the dryer is not kept well-maintained.

How much does it cost to replace a heating element in a Maytag dryer?

For Maytag dryers, it’s common for the price of a heating element to be around $40. You could easily find a heating element for a Whirlpool dryer also around $40.

You might be interested:  Quick Answer: Where To Buy Heating Element For Duet Drier?

Why is dryer not drying?

Check the Air Vent and Duct Clogged air vents are a common cause for poor airflow in clothes dryer systems. One way to see if your dryer’s air vent is clogged is by turning on your dryer and going outside to feel the flow of air leaving the vent. If it’s slow and not very warm, your vent may be due for a good cleaning.

How long should a dryer last?

The average clothes dryer lasts between eight and 12 years, according to Angie’s List. But the more you use that dryer, the shorter its lifespan is likely to be. Also, a higher-quality dryer is likely to outlast a cheaper model with inferior components.

Is it cheaper to repair or replace a dryer?

The national average cost for dryer repair is $170. If your dryer is acting strange, investing in repair services is usually much cheaper than buying a replacement dryer. New dryers cost anywhere from $400 for entry-level to $2,000, or more, for top of the line.

How much does it cost to fix a dryer that is not heating?

Fixing a dryer that does not heat averages $100 to $350. The price for this repair depends on the problem. It might be a problem with the heating element or an issue with the thermostat or igniter when using a gas dryer.

How hard is it to replace a dryer heating element?

Fortunately, replacing a heating element isn’t a terribly difficult job. You can usually find a replacement heating element at a local hardware store or online by searching for your dryer model number. Once you have the part, unplug the dryer, remove the back panel, remove the connections and install the new one.

Leave a Reply

Your email address will not be published. Required fields are marked *