Readers ask: How Do I Replace The Heating Element In My Whirlpool Duet Dryer?

Where is the heating element on Whirlpool Duet dryer?

Whirlpool usually locates the heating element on the back of dryer (must remove back of dryer) or under the drum (must remove front dryer). Be certain to disconnect power from dryer. Heating element coils look like stretched out door springs. A bad dryer heating element will have a break in the coil.

How much does it typically cost to replace a heating element in a Whirlpool Duet dryer?

A new heating element is usually between $40 and $100. This part might cost as low as $30 and as high as $200 or more, depending on the type of dryer.

How do I fix my Whirlpool Duet dryer that won’t heat?

The most common causes for a Whirlpool Duet dryer not heating are: Lint build up inside the machine or dryer venting – to prevent lint build up be sure to clean the lint out of your dryer at least once every two years and clean out your venting at least once a year.

You might be interested:  Readers ask: How To Replace Heating Element In Maytag Bravos Mct With Steam Technology?

Why is the dryer not heating up?

Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element. If you gather your tools and follow this guide, you may be able to solve basic dryer heating problems on your own.

How can you tell if the heating element in a dryer is bad?

Inspect the metal wire coil for any breaks in the wire. If the wire is solid and has no breaks in it, the heating element should be good. If the wire has a break in it, the heating element is defective.

What is the purpose of heating element?

What is a heating element? A heating element converts electrical energy into heat through the process of resistive (otherwise known as Joule heating). The electric current passing through the element encounters resistance, which produces heat.

Is it worth replacing dryer heating element?

If your dryer’s heating element burns out more than once within a year or two, the thermal fuse, which is supposed to protect it, is probably defective, so it’s a good idea to replace it. The temperature in the heating chamber may also be too high, and that may be caused by poor venting.

Is it cheaper to repair or replace a dryer?

The national average cost for dryer repair is $170. If your dryer is acting strange, investing in repair services is usually much cheaper than buying a replacement dryer. New dryers cost anywhere from $400 for entry-level to $2,000, or more, for top of the line.

You might be interested:  Quick Answer: How To Replace Whirlpool Dryer Heating Element?

How much does it cost to fix a dryer that is not heating?

Fixing a dryer that does not heat averages $100 to $350. The price for this repair depends on the problem. It might be a problem with the heating element or an issue with the thermostat or igniter when using a gas dryer.

Why did my Whirlpool dryer stop heating?

When gas or electric Whirlpool Dryer is not heating up, it usually caused by: Burnt Heating Element or Gas Valve Solenoid, Burnt Thermal Cut-Off Fuse, Defective Cycling Thermostat Or Gas Ignitor, Malfunctioned Flame Sensor.

How do you run a diagnostic on a Whirlpool Duet dryer?

press and hold for three seconds, release for three seconds; press and hold for three seconds. You’ll know you’ve entered diagnostic mode because all the indicators on the console will light up for five seconds and you’ll see the code “88” in the Estimated Time Remaining display.

How do you reset the thermal fuse on a Whirlpool dryer?

Instructions

  1. Shut off the power. Unplug the dryer to disconnect electrical power.
  2. Remove the back panel. Move the dryer forward and use a 1/4-inch nut driver to remove the screws from the back panel.
  3. Remove the fuse.
  4. Install the new thermal fuse.
  5. Reattach the back panel.
  6. Plug in the dryer.
  7. Clean the exhaust vent.

Leave a Reply

Your email address will not be published. Required fields are marked *